Reusable Content Space
Page tree
Skip to end of metadata
Go to start of metadata

Caution for use

  • When you mount the product to your equipment ensure that no mechanical stress is added, it would induce distortion such as a warp or twist. Tighten the screws as specified in the ''Mechanical Specification" section. Use screw locking techniques as necessary ( thread locker, glue on the side of the head ... )
  • When you set up the product, make sure your equipment and operators maintain a good ground to comply with ESD requirements, if this mesure is not applied te product may be damaged permanently.
  • When you install the product, make sure foreign objects do not enter the product, such as organic or metallic particules,Otherwise, malfunction or damage of the product may result.
  • If excessive shock is added to the product when, for example, the product falls, the quality of the product may be degraded. Make sure the product does not fall when you handle it.
  • Before you start using the product, test it in the actual equipment under the actual operating environment.
  • Since the product has capacitors inside, inrush current will occur during power-on. Evaluate in the actual environment in order to check the effect of the supply voltage drop by inrush current in the system.
  • If water enters the product, malfunction or damage of the product may result. If the product can be exposed to water, the system must have a waterproof structure. We do not guarantee the operation of the product when the product is exposed to condensation, dust, oil, corrosive gas (salt, acid, alkaline, or the like) , or direct sunlight.
  • This product is not designed to be radiation resistant.
  • Never use this product if the operating condition is over the absolute maximum rating. If you do, the characteristics of the product may never recover.
  • If the product is exposed to excessive exogenous noise or the like, degradation of the precision, malfunction, or damage of the product may result. The system needs to be designed so that the noise itself is suppressed or the system is immune to the noise.
  • Mechanical vibration or shock, continuous mechanical stress, rapid temperature change, or the like may cause cracks or disconnections at the various connecting parts.
  • Take sufficient safety measure for the equipment this product is built into.
  • This product is not intended for general use by the consumer but instead for engineering design. For the customer, please consider it safely with the proper use.
  • This product is not designed to be used in the equipment that demands extremely high reliability and where its failure may threaten human life or property (for example, aerospace equipment, submarine repeater, nuclear power control equipment, life support equipment, medical equipment, transportation control equipment, etc.). Therefore, Seiko Epson Corporation will not be liable for any damages caused by the use of the product for those applications.
  • Do not alter or disassemble the product. The casing of this product is electrically conductive. When the product is connected or mounted to the circuit board, ensure the board substrate or board wiring pattern does not short-circuit or contact to the case

Caution for storage

  • Do not add shock or vibration to the packing box.
  • Do not spill water over the packing box
  • Do not store or use the product in the environment where dew condensation occurs due to rapid temperature change.
  • To suppress the characteristic change by prolonged storage, it is recommended to maintain the environment at normal temperature and normal humidity. Normal temperature: +5 ~ +35 °C Normal humidity: 45%RH ~ 85%DH (JIS Z 8703).
  • Do not store the product in a location subject to High Temperature, high humidity, under direct sunlight, corrosive gas or dust.
  • Do not put mechanical stress on the product while it is stored

Other cautions

  • When you connect the socket to the header of this product, make sure you do not insert the header in the reverse orientation. If you do, the IMU may be damaged permanently. In addition, if you attach the product to the equipment, etc. using connection harness, connect the connection harness to the product first, and then attach it to the equipment, etc.
  • The gloss marks derived from the adhesive material may have appeared on the casing surface of the product, but it does not affect the function and quality of the product.
  • The Parting line as a result of die cast manufacturing process may have appeared on the casing surface of the product, but it is not an abnormality.
  • Please take care not to tamper with or accidently disturb the assembly screw on the surface where the serial number is printed when attaching and detaching the product to the system. We do not guarantee the performance and the quality of the product in case the assembly screw is manipulated


  • No labels